data she e t lead free chip resis tors rc_p series 0. 5%, 1% , 5% s izes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512 product specification C august 22, 2014 v. 0
chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 2 8 series rc_p 0100 to 2512 scope this specification describes rc series chip resistors with made by thick film process . applications ? all general purpose application features ? total lead free without rohs exemption ? halogen free epoxy ? reducing environm entally hazardous wastes ? high component and equipment reliability ? saving of pcb space global part number rc xxxx x x x xx xxxx p ( 1 ) ( 2 ) ( 3 ) ( 4 ) ( 5 ) ( 6 ) ( 7 ) ( 1 ) size 0100/0201/0402/0603/0805/1206/1210/1218/2010/2512 ( 2 ) tolerance d = 0.5 % f = 1 .0 % j = 5 .0 % ( for jumper ordering , use code of j ) ( 3 ) packaging type r = paper taping reel k = embossed taping reel s = esd safe reel (0100 only) ( 4 ) temperature coeffici ent of resistance = based on spec. ( 5 ) taping reel 07 = 7 inch dia. reel 13 =13 inch dia. reel 7n = 7 inch dia. reel, esd safe reel (0100 only) ( 6 ) resistance value there are 2~4 digits indicated the resistance value. letter r/k/m is decimal poin t . example: 97r6 = 97.6 9k76 = 9760 1m = 1,000,000 ( 7 ) default code letter p is lead free (without rohs exemption) ordering information - global part number global part numbers are identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. ordering example the ordering code for a rc0402 0.0625w chip resistor v alue 100k with 5% tolerance, supplied in 7 - inch tape reel of 10,000 units per reel is: rc0402jr - 07100kp.
chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 3 8 series rc_p 0100 to 2512 marking rc0100 / rc0201 / rc 0402 no marking rc0603 e24 series: 3 digits first two digits for significant figure and 3rd digit for number of zeros rc0805 / rc1206 / rc 1210 / rc1218 / rc20 10 / rc2512 e24/e96 series: 4 digits first three digits for significant figure and 4th digit for number of zeros note for further marking information, please see special data sheet "chip resistors marking". fig. 2 value = 10 k pf series note: construction will be adjusted to resistance value (only for pf series). fig. 3 value = 10 k construction the resistor is constructed on top of a high - grade ceramic body. internal metal electrodes are added on each end to make the contacts to the thick film resistive element. the composition of the resistive element is a noble metal imbedded into a glass and covered by a second glass to prevent environmental influences. the resistor is laser trimmed to the rated resistance value. the resistor is covered with a protective epoxy coat, finally the two external terminations (matte tin on nibarrier) are added, as shown in fig. 4 . fig. 4 chip resistor outlines o o u u t t l l i i n n e e s s for dimensions, please refer to table 1 fig. 1
chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 4 8 series rc_p 0100 to 2512 type l ( mm ) w ( mm ) h ( mm ) i 1 ( mm ) i 2 ( mm ) rc0100 0.400.02 0.200.02 0.130.02 0.100.03 0.100.03 rc0201 0.60 0.03 0.30 0.03 0.23 0.03 0.10 0.05 0.15 0.05 rc0402 1.000.05 0.500.05 0.350.05 0.200.10 0.250.10 rc0603 1.60 0.10 0.800.10 0.45 0.10 0.250.15 0.250.15 rc0805 2.00 0.10 1.250.10 0.50 0.10 0.350.20 0.350.20 rc1206 3.100.10 1.600.10 0.550.10 0.450.20 0.400.20 rc1210 3.100.10 2.600.15 0.500.10 0.45 0.15 0.500.20 rc1218 3.100.10 4.600.10 0.550.10 0.450.20 0.400.20 rc2010 5.000.10 2.500.15 0.550.10 0.450.15 0.500.20 rc2512 6.350.10 3.100.15 0.550.10 0.600.20 0.500.20 dimension table 1 electrical character istics fig. 4 chip resistor outlines table 2 type resistance range characteristics operating temperature range max. working voltage max. overload voltage dielectric withstandin g voltage temperature coefficient of resistance jumper criteria rc0100 5% (e24) 1 Q r Q 22m (0201: max.10m , 0100/ 1218: max. 1m ) 1% (e24/e96) 1 Q r Q 10m ( 0100/ 1218: max. 1m ) 0.5% (e24/e96) 10 Q r Q 1m jumper<50m C 55 c to +1 2 5 c 15v 30v 30v 1 r 10 : - 200~+6 00ppm/ 10 chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 5 8 series rc_p 0100 to 2512 fig. 5 - 1 maximum dissipation (p) in percentage of rated poweras a function of the operating ambient temperature (tamb) functional descripti on o o p p e e r r a a t t i i n n g g t t e e m m p p e e r r a a t t u u r r e e r r a a n n g g e e rc0402 to rc2512 range: - 55 to +155 (fig. 5 - 1) rc0100 to rc0201 range: - 55 to +125 (fig. 5 - 2) p p o o w w e e r r r r a a t t i i n n g g each type rated power at 70 c: rc0100=1/32w rc0201=1/20 w rc0402=1/16 w rc0603=1/10w rc0805=1/8w rc1206=1/4w rc1210=1/2w rc1218=1w rc2010=3/4w rc2512=1w rated voltage the dc or ac (rms) continuous working voltage corresponding to the rated power is deter mined by the following formula: v = where v = continuous rated dc or ac ( rms ) working voltage ( v ) p = rated power ( w ) r = resistance value ( ) packing style and pa ckaging quantity table 3 packing style and packaging quantity packing style reel dimension rc0100 rc0201 rc0402 rc0603 rc0805 rc1206 rc1210 rc1218 rc2010 rc2512 paper taping reel (r) 7" (178 mm) 20,000 10 ,000 10 ,000 5,000 5,000 5,000 5,000 --- --- --- 13" (330 mm) 80,000 50000 50000 2 0000 2 0000 2 0000 2 0000 --- --- --- esd safe reel (s) 7" (178 mm) 40,000 --- --- --- --- --- --- --- --- --- embossed taping reel 7" (178 mm) --- --- --- --- --- --- 4,000 4,000 4,000 note for tape and reel specification/dimensions, please refer to data sheet chip resistors packing. fig. 5 - 2 maximum dissipation (p) in percentage of rated poweras a function of the operating ambient temperature (tamb) footprint and soldering profiles for recommended footprint and soldering profiles, please refer to data sheet chip resistors mounting ) ( pxr
chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 6 8 series rc_p 0100 to 2512 tests and requiremen ts test test method procedure requirements temperature coefficient of resistance (t.c.r.) iec 60115 - 1 4.8 at +25/ C 55 c and +25/+125 c refer to table 2 f ormula : t.c.r= 10 6 (ppm/ c) where t 1 =+ 25 c or specified room temperature t 2 = C 55 c or + 125 c test temperature r 1 = resistance at reference temperature in ohms r 2 = resistance at test temperature in ohms life/ endurance mil - std - 202g method 108a iec 60115 - 1 4.25.1 at 70 5 for 1,000 hours; rcwv applied for 1.5 hours on and 0.5 hour off, still air required (1%+0.05 ) for d/f tol (3%+0.05 ) for j tol <100mr for jumper high temperature exposure mil - std - 202g method 108a iec 60115 - 1 4.25.3 1,000 hours at maximum operating temperature depending on specification, unpowered. (1%+0.05 ) for d/f tol (2%+0.05 ) for j tol <50mr for jumper moisture resistance mil - std - 202g method 106f iec 60115 - 1 4.24.2 each temperature / humidity cycle is defined at 8 hours (method 106f), 3 cycles / 24 hours for 10d with 25 c / 65 c 95% r.h, without steps 7a & 7b, unpowered parts mounted on test - boards, without condensation on parts (0.5%+0.05 ) for d/f tol (2%+0.05 ) for j tol <100mr for jumper humidity iec 60115 - 1 4.37 steady state for 1000 hours at 40 c / 95% r.h. rcwv applied for 1.5 hours on and 0.5 hour off (1%+0.05 ) for d/f tol (2%+0.05 ) for j tol <100mr for jumper thermal shock mil - std - 202g method 107g - 55/+125 note number of c ycles required is 300 devices mounted maximum transfer time is 20 seconds dwell time is 15 minutes. air - air (0.5%+0.05 ) for d/f tol (1%+0.05 ) for j tol <50mr for jumper short time overload iec 60115 - 1 4.13 2.5 times rcwv or maximum overload voltage which is less for 5 seconds at room temperature (1%+0.05 ) for d/f tol (2%+0.05 ) for j tol <50mr for jumper no visi ble dam age board flex/ bending iec 60115 - 1 4.33 device mounted or as described only 1 board bending required bending time: 60 5 seconds 0100/ 0201/0402:5mm; 0603/0805:3mm; 1206 and above:2mm (1%+0.05 ) for d/f/j tol <50mr for jumper no visible dam age table 8 test condition, procedure and requirements ) t t ( r r r 1 2 1 1 2 ? ?
chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 7 8 series rc_p 0100 to 2512 test test method procedure requirements solderability - wetting ipc/jedecj - std - 002b test b iec 60068 - 2 - 58 electrical test not required magnification 50x smd conditions: 1st step: method b, aging 4 hours at 155 c dry heat 2nd step: leadfree solder bath at 245 3 c dipping time: 3 0.5 seconds w ell tinned (>95% covered) no visible dam age - leaching ipc/jedecj - std - 002b test d iec 60068 - 2 - 58 leadfree solder ,260c, 30 seconds immersion time no visibl e dam age - resistance to soldering heat mil - std - 202f method 210f iec 60068 - 2 - 58 condition b, no pre - heat of samples leadfree solder, 260 c 5 , 10 1 seconds immersion time procedure 2 for smd: devices fluxed and cleaned with isopropanol (0.5%+0.05 ) for d/f tol (1%+0.05 ) for j tol <50mr for jumper no visible dam age
chip resistor su r f ac e mount www.yageo.com a ug. 22, 2014 v. 0 product specification 8 8 series rc_p 0100 to 2512 yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. any product change will be announced by pcn. revision history type power tolerance resistance range temperature coeffici ent of resistance pf 0603 1/10w, 1/5w, 3/10w, 2/5w, 1/2w 1% 2% 5% 5 m Q r < 100 m 75 ppm/c 0805 1/8w, 1/4w, 1/3w, 1/2w 4 m Q r < 100 m 1206 1/4w, 1/2w 3 m Q r < 100 m 2010 1/2w, 1w the resistors are constructed using outstanding tcr level material, which makes yageo pf resistors excellent for current sensing application in battery charger circuit & dc - dc converter. the composition of the resistive material is adjusted to give the approximate required resistance a nd is covered with a protective coating, which printed with the resistance value. finally, the three external terminations (ni / matte tin) are added, as shown in fig. 4. 5 m Q r < 100 m 2512 1w, 2w 1 m Q r < 100 m 3w 1 m Q r Q 50 m 4527 2w, 3w, 5w 6 m Q r < 1 note: 1. please cont act with sales offic es, distributors and representatives in y our region before or dering revision date change notification description version 0 aug. 2 2 , 2014 - - first issue of this specification
|
